Meet Me Down Town PHX

This content shows Simple View

Structure of a longboard

Posted on by

The detailed structure of a longboard you should know


For those who are adventurous and like to experience new things, skateboarding will be an engaging and exciting street sport. When learning about this sport, you should learn carefully about the structure of the skateboards, especially the structure of a longboard. The structure of this board includes the following parts.

Lots of young women love longboarding/


The surface of the board is the largest part of a skateboard, so this is also the most important part you need to pay attention to on how to buy a longboard.

The surface material for the long skis is mainly oak and birch wood. A plank surface will consist of many thin layers of wood pressed together.

Normally, the long skis surface will have 6 to 11 layers of plywood. If there are a few layers of wood, the board will not be firm enough and brittle. In the opposite case, the board is too thick and heavy, making it difficult for players to move and jump.

The long skateboard surface is quite large so this type of skateboard is only suitable for players who like to downhill or slide long distances.

The length of the longboard can be up to 59 inches and depending on the height you can choose for yourself a longboard. The width ranges from 9 to 10 inches.

For those of you average height who want to practice tricks, you can choose board lengths from 38 inches to 42 inches with freestyle/dancing longboard.


They are usually fitted in the wheel, allowing the wheel to move more smoothly and smoothly. Each wheel of the oil longboard will have two such ball bearings, a total of a complete skateboard will have 8 bearings.

The marbles here are usually steel, titanium, or even ceramic balls (these are extremely good and cost quite a bit, due to their durability, great hardness and very light, easy to clean).

The bearings were differentiated based on how fast they turned. The ABEC standard is commonly used, has ABEC 1,3,5,7,9 and the highest is 11 for extremely high speeds.


The wheel is the part that makes the longboard manoeuvrable.

If you are using a long skateboard to travel under the road as a vehicle or a winding pass, it is best to choose large wheels because of its good bearing capacity and high speed.

The wheel diameter size of a long skateboard is 70mm with 80A soft wheel type.

A longboard will be fitted with 4 wheels at 2 ends. That is, each truck will be fitted with 2 wheels. If you want to replace a wheel, the selected wheel is the same type, same size. These types of wheels are usually manufactured from solid rubber, which is quite hard and durable.



The surface of the board is where you can move, the truck is the part that connects the board to the wheel so that the board can slide. This is a very important element in the structure of longboards and it requires precise design and installation.

The truck is made of hard alloy, strong and has good bearing capacity. Usually, the truck is made from aluminium or titanium. There are premium trucks made from gold, carbon. These are all lightweight but very durable, good alloys, helping the player to use the longboard more easily and more permanently.

The longboards are suitable for long distances and downhill/

In which, the longest and hardest alloy bar is installed in the middle, running across the axis. They call this Axle. Hangar – the support rod is wrapped around the Axle. It has a main bearing effect. Besides, this is where the bearings will be attached.

There is also the Base Plate and Riser – gasket, Kingpin – screw and Bushing for the gasket.

Thanks to the components on this truck, you can easily control the longboard. You can adjust the tightness of screws, boards and trucks according to your preferences.

We hope that through this article you can better understand the long skateboard and have moments of relaxation while playing this street sport.

Further reading: longboard, skateboard and more…

What are the uses of a 3D pen?

Posted on by

In this modern world, it’s no longer enough to simply illustrate ideas in 2D. Such drawings served their purpose well back in the day. But thanks to the advancement in technology, everyone can now express their artistic thoughts in 3 dimensions. And that’s through the use of a 3D pen.

Do you already own one? If not, check out this amazing buying guide on Reviews Rabbit and right away order your preferred 3D pen. “What for?” You ask. Well, here’s why you need a 3D pen.

What are the uses of a 3D pen?

  1. The most obvious use of 3D pens is creating artistic objects. Think of a plastic teddy that you can strategically place on your reading table for added beauty. What about a plastic aloe vera planted in a plastic vase to beautify the entrance tour house? Yes! All that can be done using a 3D pen.
  2. Another important use is to repair items originally created using a 3D printer.  Perhaps it is a plastic doll with a broken limb. No need to throw it away. Use a 3D pen to weld the limb back into position. 
  3. If you are a student, or a teacher for that matter, make the art lessons more exciting by venturing into 3D art. Also, for non-art teachers, 3D pens are useful in illustrating important concepts. Do not endlessly speak of Victorian architecture – practically design 3D houses of Victorian characteristics and the students will really thank you. 
  4. In the manufacturing industry, 3D pens are used to create prototypes of proposed new items before they are produced in bulk.
  5. If you’ve got kids, buy them a child-friendly 3D pen. Briefly guide them on the basics and leave them to create a Mercedes Benz. I’m sure that is more engaging for the brain than picking a toy Mercedes from the supermarket shelves. 

Are 3D pens dangerous?

Generally terming 3D pens as dangerous would be inconsiderate on my part. Most of them are safe to use, but there are precautions you may need to take. First, ensure you don’t touch the nozzle of the pen while drawing. The nozzle is usually heated to high temperatures so as to melt the filament for a smooth flow. 

Another concern arises with the use of ABS filaments. These are known to emit unpleasant fumes the moment they are melted. The fumes aren’t toxic — simply unpleasant. You may therefore want to work in a well-ventilated room when using 3D pens with ABS filaments. Otherwise, if the task at hand allows, opt for the more environmentally friendly PLA filaments.


Do 3D pens work?

3D pens actually work – no doubt about this. The strength and look of the created object depends on the type of filament you use. The FLEXI or PTU filament yields a flexible object that can be twisted as you wish without breaking. PLA filaments yield quite strong objects – only that the objects have poor heat resistance properties. This is ideal for hobbyists. Objects created with ABS filaments are weaker and less rigid. Use this filament type for prototypes. 

What is the cheapest 3D pen?

Need I mention some unknown brands like Konfor and Sunfuny? Of course, there are several 3D pen brands that sell for less than 20 USD. I would however advise you to try reputable brands like MYNT3D, 3Doodler, SCRIB3D, Generic, So nice, Dikale, MIKA3D, Wacom, 3DMate, and Tecboss.  Reviews Rabbit lists some of the best 3D pens you should consider purchasing.

What is a break barrel air rifle?

Posted on by

Beginner shooters are too often dissuaded from purchasing break barrel air rifles. Why? Well, allegedly, they begin to nemd out of shape over time as a result of the manner in which they are cocked. Fact or fiction? Let us find out the facts. 

What is a break barrel air rifle

First things first.

What is meant by a break barrel air rifle?

The very name “break barrel” was derived from the manner in which the guns are cocked. To cock the gun, you need to swing the barrel on a hinge downwards to access the breech – this is what is referred to as breaking the barrel. 

You then load the pellet and swing the barrel up into position. This compresses the powerful mainspring, which serves as the powerplant of the airgun. 

break barrel air rifle

Just in front of the spring, we have a piston whose sear locks into position. The spring now has stored elastic energy, waiting for the pull of the trigger.

The moment you pull the trigger, the sear disengages and allows the piston to be forcefully pushed forward. This piston movement additionally pressurizes the air in front of it. 

To cock the gun you need to swing the barrel on a hinge

The piston usually sits in the compression chamber, which is connected to the barrel through the air transfer port. In front of the air transfer port sits the pellet. As expected, the pellet is forcefully propelled forward down the barrel and out into the air.

How to make a break barrel air rifle more powerful

The power of the break barrel mostly comes from the kind of spring used in the gun. In this regard, you can make the airgun more powerful by replacing the spring with another one that can store greater elastic energy when compressed. Ideally, the spring should have thicker coils but be of similar external diameter to the current one. 

I would however point out here that you need quite some skill to disassemble the gun, replace the spring, and reassemble the airgun. If you are not a really good DIYer, you better leave it to professionals.

How to make a break barrel air rifle more powerful

Note that the more powerful the spring is the stiffer it will be. And so the resulting cocking effort will be greater than you are used to. 

Another method involves marginally reducing the size of the air transfer port. You can achieve this by inserting a plug and drilling a smaller hole in it. This makes the break barrel airgun more powerful by increasing the air pressure behind the pellet. If it sounds quite difficult for you, I wouldn’t advise you to mess around. Engage an experienced air rifle technician or simply purchase a more powerful break barrel air rifle. 

What is a good scope for a break barrel air rifle?

One outstanding characteristic of break barrel air rifles is the heavy recoil felt after firing the pellet. The laws of motion dictate that for every action, there must be an equal and opposite reaction.

good scope for a break barrel air rifle

Once the spring is powerfully released from its resting position, the next thing for it is to jerk backward in an almost similar powerful motion. 

Therefore, the scope chosen for the air rifle must be able to withstand this heavy recoil without breaking.  

How to sight in a break barrel air rifle

The first thing to do with your new break barrel airgun is to align its sights with the flight path of the ammo. So get a good pair of shooting glasses, set up a reliable paper target with a sturdy backstop. 

Standing about 15 feet from the target, take three shots, and carefully note the points the pellets land on the paper. If the pellets land directly on the targeted points, you can try a few more times to see whether the accuracy is consistent.

How to sight in a break barrel air rifle

However, if the pellets land too low or too high, you need to adjust the scope or open sights bit by bit until you are able to hit the target. Try moving some feet away and test whether the air rifle is still accurate.


You definitely need more details on the advantages and disadvantages of different break barrel air rifles, and how to choose the best. Airgun Maniac reviews in great detail some of the best break barrel air rifles in the market. Check out the guide and make an informed choice.

How To Identify Broken Diode, By Digital Multimeter.

Posted on by

What is a diode?

A diode is an electrical component, a semiconductor device that allows the current to flow in one direction


– Rectification current, ie convert alternating current into direct current.

– One-way power switch

So when does the diode fail? It prevents current from flowing in two directions (open diode) or current flows in two directions (short diode). You can see how to check the diode below.

How to test diodes

Digital multimeters can test diodes using one of two methods:

  1. Diode Test mode: almost always the best approach.
  2. Resistance mode: typically used only if a multimeter is not equipped with a Diode Test mode.

Note: In some cases, it may be necessary to remove one end of the diode from the circuit in order to test the diode.

Things to know about the Resistance mode when testing diodes:

  • Does not always indicate whether a diode is good or bad.
  • Should not be taken when a diode is connected in a circuit since it can produce a false reading.
  • CAN be used to verify a diode is bad in a specific application after a Diode Test indicates a diode is bad.

A diode is best tested by measuring the voltage drop across the diode when it is forward-biased. A forward-biased diode acts as a closed switch, permitting current to flow.

A multimeter’s Diode Test mode produces a small voltage between test leads. The multimeter then displays the voltage drop when the test leads are connected across a diode when forward-biased. The Diode Test procedure is conducted as follows:

  1. Make certain a) all power to the circuit is OFF and b) no voltage exists at the diode. Voltage may be present in the circuit due to charged capacitors. If so, the capacitors need to be discharged. Set the multimeter to measure ac or dc voltage as required.
  2. Turn the dial (rotary switch) to the Diode Test mode (  ). It may share a space on the dial with another function.
  3. Connect the test leads to the diode. Record the measurement displayed.
  4. Reverse the test leads. Record the measurement displayed.

Diode test analysis

  • A good forward-based diode displays a voltage drop ranging from 0.5 to 0.8 volts for the most commonly used silicon diodes. Some germanium diodes have a voltage drop ranging from 0.2 to 0.3 V.
  • The multimeter displays OL when a good diode is reverse-biased. The OL reading indicates the diode is functioning as an open switch.
  • A bad (opened) diode does not allow current to flow in either direction. A multimeter will display OL in both directions when the diode is opened.
  • A shorted diode has the same voltage drop reading (approximately 0.4 V) in both directions.

A multimeter set to the Resistance mode (Ω) can be used as an additional diode test or, as mentioned previously if a multimeter does not include the Diode Test mode.

A diode is forward-biased when the positive (red) test lead is on the anode and the negative (black) test lead is on the cathode.

  • The forward-biased resistance of a good diode should range from 1000 Ω to 10 MΩ.
  • The resistance measurement is high when the diode is forward-biased because the current from the multimeter flows through the diode, causing the high-resistance measurement required for testing.

A diode is reverse-biased when the positive (red) test lead is on the cathode and the negative (black) test lead is on the anode.

  • The reverse-biased resistance of a good diode displays OL on a multimeter. The diode is bad if readings are the same in both directions.

The resistance mode procedure is conducted as follows:

  1. Make certain a) all power to the circuit is OFF and b) no voltage exists at the diode. Voltage may be present in the circuit due to charged capacitors. If so, the capacitors need to be discharged. Set the multimeter to measure ac or dc voltage as required.
  2. Turn the dial to Resistance mode (Ω). It may share a space on the dial with another function.
  3. Connect the test leads to the diode after it has been removed from the circuit. Record the measurement displayed.
  4. Reverse the test leads. Record the measurement displayed.
  5. For best results when using the Resistance mode to test diodes, compare the readings taken with a known good diode.


See more:

Soft Tip Darts And Steel Tip Darts: What Should I Choose?

Posted on by

The game of darts may simply look entertaining, however, like any other game, it requires several skills, luck, and physics. Choosing what type of dart you will use is the first step in determining your play style. So, Have you ever asked yourself: “Between soft tip darts and steel tip darts: what should I choose? “

Let’s find out the answer in the article right below!

Playing darts



Steel Tip Darts

Steel tip darts have been utilized by the game’s ancestors when it was first played. The act of throwing darts originated from a pastime activity for soldiers including throwing metal arrowheads.

steel tip darts

Due to its history, steel tip darts are highly appreciated among the world of dart players. Some of them even bear in mind the thought that using soft tip darts is disrespectful. For that reason, do steel tip darts worth the hype or are they overrated due to history?

Well, we must say that it’s a firm YES. Many benefits can be drawn from using steel tip darts in the game:

  • Their weights are more significant (ranging from 20-30 grams) which allows the players to produce heavier and precise throws.
  • Not only being an inexpensive material in production, but steel also empowers dart tips and increases their inner strength. They are not likely to snap or bend for long-term usage, ensuring your investment in these tip darts is valuable.

darts contruction

We must always refer back to the traditional aspect. Using steel dart tips is an excellent choice if you tend to stick to the old-school characteristics. Playing dart, in the mind of some serious dart players, implies utilizing steel dart tips. We sure you will have a wonderful darting time with these steel dart tips.

See More: Best Bristle Dart Boards Review 2020


Soft Tip Darts

Soft tip darts are recently adopted by the dart families, however, they have proven themselves to exceed dart playing communities’ expectations with their phenomenal behaviors.

soft tip darts

Under the correct conditions, plastic tip darts can offer unparalleled accommodation which settles on them the ideal decision for certain individuals.

As the name suggests, soft tip darts are fabricated utilizing shaped plastic which settles on the title of “safe play”. Unless you deliberately throw a soft tip in someone’s eyes, no one can get injured by a soft-tip. These criteria cannot be applied to steep tip darts, unfortunately.

There have been reports of accidents where players throwing darts off-target, eventually hurt themselves.

On the off chance, you want throwing darts is a family activity, soft tip darts are the one to go for to maintain everyone’s safety and ensure quality playing time.

The same rules apply if you or your friends are at the beginner level of throwing darts. By using soft plastic tip darts, you will altogether limit the danger of injury.

Digital dartboards are designed to fit in with the modern lifestyle nowadays. If you don’t want to waste time calculating the scores in competition, the digital board will do that for you on the condition of solidly using soft tip darts.

best electronic dartboard

Playing darts at home hidden the risk of destroying the surrounding walls, nearby household appliances. In this way, your most logical option might be to go with soft plastic tips.

These advantages, sadly, include some significant downfalls (actually). Soft plastic tip darts are increasingly inclined to break down often. Hence, you should replace them regularly to keep the game going.

You may also like: Top 10 Best Electronic Dart Boards For Endless Fun


Soft Tip Darts And Steel Tip Darts: What Should I Choose?

This question can be answered with no ease as long as you determine the answers for the following questions.

Where are you playing, and who are you playing with? Answer these two and you will realize the best option for your situation.

Are you in a league or professional competitions? In this case, steel tip darts are the ones to go for. Otherwise, if you just keep it simple as a daily pastime, soft tip darts are your next shopping target.



We hope you successfully find out the answer to: “Soft tip darts and steel tip darts: what should I choose?”. Both darts have their ups and downs, but the choice is yours to find out the one that suits your needs most.

Thank you for reading our article and have a great time throwing darts!


Further Reading: How To Choose Best Darts For Beginners



How To Set Up A Tent In A Windy Place

Posted on by

The wind made many people miserable when camping far away from the city, especially the hilltop campsites, without trees. Perhaps the most difficult task you face right now is setting up camp in windy weather. Below, I will show you how to set up an effective tent in a windy place.



1. Choose an appropriate tent location

When choosing a location to pitch your tent, consider where the wind is blowing. Place the narrowest side of the tent, usually the base of the tent in the direction of the wind, so that the tent won’t easily fly away. Besides, you can take advantage of naturally available things like trees or rocks to block the wind.

2. Use heavy equipment as anchor points

Heavier items are often used to anchor tents, such as boulders, logs, etc.


3. Connect the first tent bone

Before removing the tent and tent cover from the carrying case, install the tent bone first. Once the tent meets the wind, the tent will be blown away and you will be hard to control, so you need to have the tent bone right away to tame and frame the tent, so it will be easier to control.

4. Pile the tent at the tent face facing the wind

When you have two tent piles in hand, remove the tent body first. Hold the tent towards the wind and let the wind blow the tent body away from you. Soon, pile the tent in front for this side.

Note: Spread the back tent cover.

5. Attach tent bone to the tent body

And now, place the tent bone on top of the tent to hold the tent first. Start fitting the tent bone from the side of the tent you just made. Then pile the other side and continue to mount the tent bone.

Tip: For now, throw heavier items like backpacks into the tent to secure the tent.

6. Tie tent covers

When you take out the tent cover, hold on to the side of the tent cover, let the wind blow to raise the cover over the tent. If you go alone, this will be the most difficult part of running back and forth to tie each point on the sheet to the tent bone.

7. Make sure the tent is secure

It is very important to make a tent, make it stronger and resist wind power. If the assembly is loose, the tent will be very easily damaged by strong wind.

Make your Longboard Faster with Four Easy Approaches

Posted on by

Four simple methods to make your Longboard faster

Refer to the following ways to speed up the longboard, causing ardenaline levels to rise in the blood

Skateboard improves its stability and durability to create longboard, and makes many skateboard fans love them.

However, the way to accelerate longboard is not well known

If you do, keep reading below to find your answer.


How to make your longboard faster?

Method 1: Make sure the bearings are well adjusted

dirt and mud accumulated during the ride will prevent the bearings from sliding.

Make your longboard faster by cleaning and lubricating bearings.

Step 1: remove the bearings

First, gently remove the first bearing from the axle

Then change sides and remove the 2nd bearing from the axle

Step 2: clean the bearings

Use a clean cloth to remove mud and dust from the bearing

Then dip the bearing into a container of clean water for 2 minutes to bring the best results

rotate the bearing for 1 minute to remove dirt from the bearing

At the end of this step, remove the bearings and allow them to dry

Step 3: lubricate bearings

After the bearing has dried, apply 1 to 2 drops of lubricant to the bearing and rotate for 1 minute for best results

Method 2: change your wheels

Wheels have a very important impact on the speed of the longboard.

Inappropriate wheel diameter and material can slow down your longboard speed

Please pay attention to these 2 things to ensure the speed for the longboard

  • replace the larger diameter wheels

Small wheels make the longboard boot faster, but the big wheels make the skating speed faster. Try replacing small wheels with big wheels to achieve the longboard high-speed experience

  • choose good quality wheels

Cheap longboard will have low wheel quality.

After a period of use it will reduce quality and not recover, making your longboard slow down when sliding

High quality wheels with good connection and strong core, help to make the longboard sliding faster

Readmore: Cruiser Vs Longboard – what is different ?

Method 3: Improve your skating skills

This method does not involve longboard editing, but it starts from yourself

You need to improve your skating skills every day to get the best experience of high speed longboard

Here are some of our suggestions

  • be more confident and more confident

Your frustration is the biggest obstacle that stops you with high speed longboard

Believe in your abilities, and practice day by day, you will soon achieve good results

  • equip yourself with protective gear

Protective gear is needed for high speed slide longboard beginners

Standard kit includes helmet, elbow guards, knee protectors

Prepare enough of these protective gear before becoming a high-speed longboard skating expert

  • Tame speed wobbles

The wobble between you and the skateboard is incompatible with the high speed longboard

Be sure to crouch down to reduce the resistance between you and your surroundings, to get the best speed

related: Review a longboard such as Atom Drop Through Longboard

Method 4: choose the appropriate route

If you want to slide high-speed longboard, do not choose the rough, bumpy roads

Choose for yourself a familiar and smooth, deserted path. That will help you to be able to achieve high speeds with the longboard

However, if you want to slide the longboard faster on smooth roads then you need to choose the wheels with good quality.

because low quality wheels absorb more friction and reduce your skid speed

Last line

The above are 4 methods to speed up your longboard sliding, except method 3 is to improve the sliding technique

From these tutorials we hope you’ll enhance your experience with the high speed longboard

wish you happy

further reading: